It sounds like you are wanting to install a single crossbar on the bed of your 2002 Chevy S-10 to go with your already installed crossbar. There are not any single crossbars that you can add so you would need to install a complete truck bed rack such as Erickson Truck Bed Ladder Rack w/ Load Stops - Steel - 800 lbs # EM07706. Or you could go with a more affordable setup like Erickson Truck Bed Ladder Rack - Side Mount - Steel - 250 lbs # EM07708. This mounts on one side of the truck bed... view full answer...
For your 2003 Chevy S10 ZR2 4WD we have the Draw Tite hitch part # 65004 as a confirmed fit. The Curt hitch # 31021 that you referenced does not fit the ZR2 models. view full answer...
In order to determine which of the wires coming from the stoplight switch of your 2003 Chevy S10 should be used to install a brake controller you will need to use a circuit tester like part # PTW2993 to test the wires till you find one that sees voltage when the brakes are applied and none when they are released. We don't have specific wire color info for your vehicle, but testing the wires will be pretty easy and will tell you which one to use. view full answer...
Sounds like you have the Sportside with a non towing bumper which would mean you would want the part # 75085. If instead you had the factory roll pan bumper you would want the pat # 13920.
I attached a picture of what the sportside with non-towing bumper looks like. If that matches your truck you would want the # 75085. view full answer...
I did some research and found that the manual for the 2000 Chevrolet S-10 pickup states that the vehicle is not to be flat-towed. The manual states that the transmission is not designed to allow it to be towed behind another vehicle.
The suggestion in the manual is to place the truck with all four wheels on a dolly like a car hauler. I wish I had better news for you but I cannot recommend anything that will allow you to flat-tow your S-10. view full answer...
We do have a replacement that will work for you, even though the lid alone is not available separately; however, the inlet of the Furrion RV Power Cord Conversion Kit 125V - 30 Amp is something you can get.
What you need is the Furrion 30 Amp Power Inlet - White - LED # 431861 which has the Powersmart LED indicator and is the same power inlet used in the kit so you do not have to purchase the entire kit, you can just get the inlet.
I have added a link to a video review of this inlet... view full answer...
I just spoke with my rep at Extang and he confirmed that the item # EX37560 is the full tilt replacement cover for your 1997 Chevrolet S-10 fleetside truck. view full answer...
The Pacer Performance 3rd Brake Light Logic Module # PP20-702 filters out the turn signal and only illuminates the 3rd brake light when the brake pedal is pressed. I have attached a photo of the installation instructions for you to check out. view full answer...
I wouldn't recommend doing that, as it will reduce the structural integrity of the bumper. Most towing bumpers are only rated for 3500 lbs, and a trailer that would use a 2-5/16 ball is typically heavier than that. You'd want to use the receiver hitch shown in your photo, rather than mounting a ball in your bumper. view full answer...
The Vision X Headlight Conversion Kit # VX-46 does fit your 1994 Chevrolet S10. They are sold as a a pair, so you can replace both the driver's and passenger's headlight.
The headlights use a 9007 bulb, which is different than the factory, however the conversion kit comes with an adapter to plug your factory pigtail into, and then into the bulb. When paired with Vision X bulbs, they can produce up to 60 % more light output than the factory housing, and 30 % more light output when using... view full answer...
The RoadActive Suspension Kit # RAS4527-T will typically raise the rear of your 2001 Chevy S-10 about 1/2 to 3/4 of an inch. If you would like to raise your truck the tension can be adjusted and you can get about 1-1/4 inches of lift.
Its main purpose will be to prevent sag when carrying a heavy load. view full answer...
In order to make a proper selection for a hitch ball, you will need to find out what diameter size ball your trailer needs. It should be stamped on the trailer coupler or frame, either 1-7/8 or 2 inch.
All bumper ball holes are 3/4 of an inch, so you will need to pick a ball with a 3/4 inch shank diameter. The ball you were looking at, part # A-82, is a 3/4 inch shank diameter and is a 2 inch diameter ball. If you need a 1-7/8 inch ball, you would use part # A-80. Those are our only stainless... view full answer...
Curt Class III trailer hitch # C13021 fits the following vehicles:
1982 - 2004 Chevrolet S-10 Pickup with Factory Step Bumper
1982 - 1990 GMC S-15 Pickup with Factory Step Bumper
1991 - 2004 GMC Sonoma with Factory Step Bumper
1996 - 2000 Isuzu Hombre with Step Bumper
If you are selling a hitch the hardware cannot be reused. It is meant to be torqued down one time only. So for replacement hardware use # RHK, enter the hitch number and manufacturer where indicated on the RHK page, then... view full answer...
Hey Pedro!
The 3" Westin Signature Series Round Nerf Bars # 25-0675 is what I recommend using for your 2002 Chevy S-10 because they are they tried and true step version designed for your S-10. If you're looking for smaller wheel hoops then this will still be your best option because nobody makes custom wheel hoops that fit your truck. view full answer...
Yes, the Brake Buddy Select 3 item # HM39524 will work with your 1998 Chevy Blazer. It has a built in charge line kit that will keep your battery charged while you are traveling. I have attached an installation video along with the instructions so you can see how to set this up.
As far as baseplate goes. Since you have the 4WD model you will want the Roadmaster Direct-Connect Base Plate Kit item # 179-8. This kit fits all models except for the ZR-2. There are no base plate kits for the... view full answer...
The correct hitch will depend on which bumper your S-10 is equipped with.
For a factory step bumper, I'd recommend the Curt # C13132. For a roll pan bumper, you'll want to use # 13920, but you'll need to cut a hole in the license plate well and find an old-school hinged license plate holder online or from a salvage yard.
If you have a short bed truck, the # 13920 hitch will prevent the spare tire from being stowed under the vehicle. view full answer...
According to my AirLift representative, their Ride Control system, part # AL59535 is compatible with the ZQ8 suspension on your 2003 Chevy S-10. view full answer...
My technical contact at Hopkins confirmed that if the Hopkins Agility brake controller # HM47294 that you referenced is installed correctly your settings are saved in the memory when the engine on your 1996 Chevy S-10 pick-up is turned off. If you bypass the installation instructions and run it through your fuse panel then the brake controller may shut off and need to be re-set each time your vehicle is started.
According to the installation instructions which I have attached you will... view full answer...
Assuming your Extang Tuff Tonno is part # EX14525, the replacement tarp is # EX13525. The replacement is specific to that particular # EX14525, so if you have a different tonneau cover, please let me know. view full answer...
According to Curt, when installing trailer hitch # 13920 on a 1992 Chevy S-10 with the factory roll pan bumper you only have to relocate the spare tire if the truck is a short bed model (6 foot bed). I have included a link to the installation instructions for you. This is the only hitch for models with the roll pan bumper.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4... view full answer...